Name
tcclasses — Shorewall file to define HTB and HFSC classes
Synopsis
/etc/shorewall/tcclasses
Description
A note on the rate/bandwidth definitions used in this file:
don't use a space between the integer value and the unit: 30kbit is valid while 30 kbit is NOT.
you can use one of the following units:
- kpbs
Kilobytes per second.
- mbps
Megabytes per second.
- kbit
Kilobits per second.
- mbit
Megabits per second.
- bps or number
Bytes per second.
if you want the values to be calculated for you depending on the output bandwidth setting defined for an interface in tcdevices, you can use expressions like the following:
- full/3
causes the bandwidth to be calculated as 1/3 of the full outgoing speed that is defined.
- full*9/10
will set this bandwidth to 9/10 of the full bandwidth
Note that in a sub-class (a class that has a specified parent class), full refers to the RATE or CEIL of the parent class rather than to the OUT-BANDWIDTH of the device.
DO NOT add a unit to the rate if it is calculated !
The columns in the file are as follows.
- INTERFACE - interface[[:parent]:class]
Name of interface.
You may specify the interface number rather than the interface name. If the classify option is given for the interface in shorewall-tcdevices(5), then you must also specify an interface class (an integer that must be unique within classes associated with this interface). If the classify option is not given, you may still specify a class or you may have Shorewall generate a class number from the MARK value. Interface numbers and class numbers are always assumed to be specified in hex and class number 1 is reserved as the root class of the queuing discipline.
You may NOT specify wildcards here, e.g. if you have multiple ppp interfaces, you need to put them all in here!
Please note that you can only use interface names in here that have a bandwidth defined in the shorewall-tcdevices(5) file.
Normally, all classes defined here are sub-classes of a root class that is implicitly defined from the entry in shorewall-tcdevices(5). You can establish a class hierarchy by specifying a parent class -- the number of a class that you have previously defined. The sub-class may borrow unused bandwidth from its parent.
- MARK - {-|value}
The mark value which is an integer in the range 1-255. You set mark values in the shorewall-mangle(5) file, marking the traffic you want to fit in the classes defined in here. Must be specified as '-' if the classify option is given for the interface in shorewall-tcdevices(5) and you are running Shorewall 4.5.5 or earlier.
You can use the same marks for different interfaces.
- RATE - {-|rate[:dmax[:umax]]}
The minimum bandwidth this class should get, when the traffic load rises. If the sum of the rates in this column exceeds the INTERFACE's OUT-BANDWIDTH, then the OUT-BANDWIDTH limit may not be honored. Similarly, if the sum of the rates of sub-classes of a class exceed the CEIL of the parent class, things don't work well.
When using the HFSC queuing discipline, this column specify the real-time (RT) service curve. leaf classes may specify
dmax, the maximum delay in milliseconds that the first queued packet for this class should experience. May be expressed as an integer, optionally followed by 'ms' with no intervening white-space (e.g., 10ms).HFSC leaf classes may also specify
umax, the largest packet expected in this class. May be expressed as an integer. The unit of measure is bytes and the integer may be optionally followed by 'b' with no intervening white-space (e.g., 800b).umaxmay only be given ifdmaxis also given.Beginning with Shorewall 4.5.6, HFSC classes may omit this column (e.g, '-' in the column), provided that an
lsrateis specified (see CEIL below). These rates are used to arbitrate between classes of the same priority.- CEIL - [lsrate:]rate
The maximum bandwidth this class is allowed to use when the link is idle. Useful if you have traffic which can get full speed when more needed services (e.g. ssh) are not used.
You can use the value full in here for setting the maximum bandwidth to the RATE of the parent class, or the OUT-BANDWIDTH of the device if there is no parent class.
Beginning with Shorewall 4.5.6, you can also specify an
lsrate(link sharing rate).- PRIORITY - priority
For HTB:
The priority in which classes will be serviced by the packet shaping scheduler and also the priority in which bandwidth in excess of the rate will be given to each class.
Higher priority classes will experience less delay since they are serviced first. Priority values are serviced in ascending order (e.g. 0 is higher priority than 1).
Classes may be set to the same priority, in which case they will be serviced as equals.
For both HTB and HFSC, the priority is used to calculate the priority of following Shorewall-generated classification filters that refer to the class:
Packet MARK
tcp-ack and the tos options (see below)
The rules for classes with lower numeric priorities will appear before those with higher numeric priorities.
Beginning with Shorewall 4.5.8, the PRIORITY may be omitted from an HFSC class if you do not use the MARK column or the tcp-ack or tos options. If you use any of those features and omit the PRIORITY, then you must specify a
priorityalong with the MARK or option.- OPTIONS (Optional) - [option[,option]...]
A comma-separated list of options including the following:
- default
This is the default class for that interface where all traffic should go, that is not classified otherwise.
Note
You must define default for exactly one class per interface.
- tos=0xvalue[/0xmask][:
priority] (mask defaults to 0xff) This lets you define a classifier for the given value/mask combination of the IP packet's TOS/Precedence/DiffSrv octet (aka the TOS byte).
Beginning with Shorewall 4.5.8, the
value/maskmay be followed by a colon (":") and apriority. This priority determines the order in which filter rules are processed during packet classification. If not specified, the value (class priority<< 8) | 10) is used.- tos-tosname[:
priority] Aliases for the following TOS octet value and mask encodings. TOS encodings of the "TOS byte" have been deprecated in favor of diffserve classes, but programs like ssh, rlogin, and ftp still use them.
Beginning with Shorewall 4.5.8, the
tos-namemay be followed by a colon (":") and apriority. This priority determines the order in which filter rules are processed during packet classification. If not specified, the value (class priority<< 8) | 10) is used.tos-minimize-delay 0x10/0x10 tos-maximize-throughput 0x08/0x08 tos-maximize-reliability 0x04/0x04 tos-minimize-cost 0x02/0x02 tos-normal-service 0x00/0x1e
Note
Each of these options is only valid for ONE class per interface.
- tcp-ack[:
priority] If defined, causes a tc filter to be created that puts all tcp ack packets on that interface that have a size of <=64 Bytes to go in this class. This is useful for speeding up downloads. Please note that the size of the ack packets is limited to 64 bytes because we want only packets WITHOUT payload to match.
Beginning with Shorewall 4.5.8, the tcp-ack may be followed by a colon (":") and a
priority. This priority determines the order in which filter rules are processed during packet classification. If not specified, the value (class priority<< 8) | 20) is used.Note
This option is only valid for ONE class per interface.
- occurs=number
Typically used with an IPMARK entry in tcrules. Causes the rule to be replicated for a total of number rules. Each rule has a successively class number and mark value.
When 'occurs' is used:
The associated device may not have the 'classify' option.
The class may not be the default class.
The class may not have any 'tos=' options (including 'tcp-ack').
The class should not specify a MARK value. If one is specified, it will be ignored with a warning message.
The 'RATE' and 'CEIL' parameters apply to each instance of the class. So the total RATE represented by an entry with 'occurs' will be the listed RATE multiplied by number. For additional information, see shorewall-tcrules (5).
- flow=keys
Shorewall attaches an SFQ queuing discipline to each leaf HTB class. SFQ ensures that each flow gets equal access to the interface. The default definition of a flow corresponds roughly to a Netfilter connection. So if one internal system is running BitTorrent, for example, it can have lots of 'flows' and can thus take up a larger share of the bandwidth than a system having only a single active connection. The
flowclassifier (module cls_flow) works around this by letting you define what a 'flow' is. The classifier must be used carefully or it can block off all traffic on an interface! The flow option can be specified for an HTB leaf class (one that has no sub-classes). We recommend that you use the following:Shaping internet-bound traffic: flow=nfct-src Shaping traffic bound for your local net: flow=dst These will cause a 'flow' to consists of the traffic to/from each internal system.
When more than one key is give, they must be enclosed in parenthesis and separated by commas.
To see a list of the possible flow keys, run this command:
tc filter add flow help
Those that begin with "nfct-" are Netfilter connection tracking fields. As shown above, we recommend flow=nfct-src; that means that we want to use the source IP address before NAT as the key.
- pfifo
When specified for a leaf class, the pfifo queuing discipline is applied to the class rather than the sfq queuing discipline.
- limit=number
Added in Shorewall 4.4.3. When specified for a leaf class, determines the maximum number of packets that may be queued within the class. The number must be > 2 and <=128. If not specified, the value 127 is assumed.
- red=(
redoption=value, ...) Added in Shorewall 4.5.6. When specified on a leaf class, causes the class to use the RED (Random Early Detection) queuing discipline rather than SFQ. See tc-red (8) for additional information.
Allowable
redoptionsare:- min
min Average queue size at which marking becomes a possibility.
- max
max At this average queue size, the marking probability is maximal. Must be at least twice
minto prevent synchronous retransmits, higher for lowmin.- probability
probability Maximum probability for marking, specified as a floating point number from 0.0 to 1.0. Suggested values are 0.01 or 0.02 (1 or 2%, respectively).
- limit
limit Hard limit on the real (not average) queue size in bytes. Further packets are dropped. Should be set higher than
max+burst. It is advised to set this a few times higher thanmax. Shorewall requires thatlimitbe at least twicemin.- burst
burst Used for determining how fast the average queue size is influenced by the real queue size. Larger values make the calculation more sluggish, allowing longer bursts of traffic before marking starts. Real life experiments support the following guide‐line: (
min+min+max)/(3*avpkt).- avpkt
avpkt Optional. Specified in bytes. Used with burst to determine the time constant for average queue size calculations. 1000 is a good value and is the Shorewall default.
- bandwidth
bandwidth Optional. This rate is used for calculating the average queue size after some idle time. Should be set to the bandwidth of your interface. Does not mean that RED will shape for you!
- ecn
RED can either 'mark' or 'drop'. Explicit Congestion Notification allows RED to notify remote hosts that their rate exceeds the amount of bandwidth available. Non-ECN capable hosts can only be notified by dropping a packet. If this parameter is specified, packets which indicate that their hosts honor ECN will only be marked and not dropped, unless the queue size hits
limitbytes. Recommended.
- min
- fq_codel[=(
codeloption=value, ...)] Added in Shorewall 4.5.12. When specified for a leaf class, causes the class to use the FQ_CODEL (Fair-queuing Controlled Delay) queuing discipline rather than SFQ. See tc-fq_codel (8) for additional information.
Allowable
codeloptionsare:- limit
hard limit on the real queue size. When this limit is reached, incoming packets are dropped. If the value is lowered, packets are dropped so that the new limit is met. Default is 1000 packets.
- flows
is the number of flows into which the incoming packets are classified. Due to the stochastic nature of hashing, multiple flows may end up being hashed into the same slot. Newer flows have priority over older ones. This parameter can be set only at load time since memory has to be allocated for the hash table. Default value is 1024.
- target
is the acceptable minimum standing/persistent queue delay. This minimum delay is identified by tracking the local minimum queue delay that packets experience. Default and recommended value is 5ms.
- interval
is used to ensure that the measured minimum delay does not become too stale. The minimum delay must be experienced in the last epoch of length interval. It should be set on the order of the worst-case RTT through the bottleneck to give endpoints sufficient time to react. Default value is 100ms.
- quantum
is the number of bytes used as 'deficit' in the fair queuing algorithm. Default is set to 1514 bytes which corresponds to the Ethernet MTU plus the hardware header length of 14 bytes.
- ecn | noecn
can be used to mark packets instead of dropping them. If ecn has been enabled, noecn can be used to turn it off and vice-versa. By default, ecn is enabled.
Examples
- Example 1:
Suppose you are using PPP over Ethernet (DSL) and ppp0 is the interface for this. You have 4 classes here, the first you can use for voice over IP traffic, the second interactive traffic (e.g. ssh/telnet but not scp), the third will be for all unclassified traffic, and the forth is for low priority traffic (e.g. peer-to-peer).
The voice traffic in the first class will be guaranteed a minimum of 100kbps and always be serviced first (because of the low priority number, giving less delay) and will be granted excess bandwidth (up to 180kbps, the class ceiling) first, before any other traffic. A single VoIP stream, depending upon codecs, after encapsulation, can take up to 80kbps on a PPPoE/DSL link, so we pad a little bit just in case. (TOS byte values 0xb8 and 0x68 are DiffServ classes EF and AFF3-1 respectively and are often used by VOIP devices).
Interactive traffic (tos-minimum-delay) and TCP acks (and ICMP echo traffic if you use the example in tcrules) and any packet with a mark of 2 will be guaranteed 1/4 of the link bandwidth, and may extend up to full speed of the link.
Unclassified traffic and packets marked as 3 will be guaranteed 1/4th of the link bandwidth, and may extend to the full speed of the link.
Packets marked with 4 will be treated as low priority packets. (The tcrules example marks p2p traffic as such.) If the link is congested, they're only guaranteed 1/8th of the speed, and even if the link is empty, can only expand to 80% of link bandwidth just as a precaution in case there are upstream queues we didn't account for. This is the last class to get additional bandwidth and the last to get serviced by the scheduler because of the low priority.
#INTERFACE MARK RATE CEIL PRIORITY OPTIONS ppp0 1 100kbit 180kbit 1 tos=0x68/0xfc,tos=0xb8/0xfc ppp0 2 full/4 full 2 tcp-ack,tos-minimize-delay ppp0 3 full/4 full 3 default ppp0 4 full/8 full*8/10 4
See ALSO
http://www.shorewall.net/traffic_shaping.htm
http://www.shorewall.net/configuration_file_basics.htm#Pairs
tc-hfsc(7)
tc-red(8)
shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5), shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5), shorewall-secmarks(5), shorewall-tcdevices(5), shorewall-mangle(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5)
