Copyright © 2001-2009 Thomas M. Eastep
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover, and with no Back-Cover Texts. A copy of the license is included in the section entitled “GNU Free Documentation License”.
2016/02/16
Table of Contents
Caution
This article applies to Shorewall 4.3 and later. If you are running a version of Shorewall earlier than Shorewall 4.3.5 then please see the documentation for that release.
The traditional net-tools contain a program called
ifconfig which is used to configure network devices.
ifconfig introduced the concept of aliased or
virtual interfaces. These virtual interfaces have
names of the form interface:integer (e.g., eth0:0) and ifconfig treats them more or
less like real interfaces.
Example 1. ifconfig
[root@gateway root]# ifconfig eth0:0
eth0:0 Link encap:Ethernet HWaddr 02:00:08:3:FA:55
inet addr:206.124.146.178 Bcast:206.124.146.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11 Base address:0x2000
[root@gateway root]# The ifconfig utility is being gradually phased out in favor of the ip utility which is part of the iproute package. The ip utility does not use the concept of aliases or virtual interfaces but rather treats additional addresses on an interface as objects in their own right. The ip utility does provide for interaction with ifconfig in that it allows addresses to be labeled where these labels take the form of ipconfig virtual interfaces.
Example 2. ip
[root@gateway root]# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb qlen 100
link/ether 02:00:08:e3:fa:55 brd ff:ff:ff:ff:ff:ff
inet 206.124.146.176/24 brd 206.124.146.255 scope global eth0
inet 206.124.146.178/24 brd 206.124.146.255 scope global secondary eth0:0
[root@gateway root]# Note
One cannot type
“ip addr show dev eth0:0” because
“eth0:0” is a
label for a particular address rather than a device name.
[root@gateway root]# ip addr show dev eth0:0
Device "eth0:0" does not exist.
[root@gateway root]#The iptables program doesn't support virtual interfaces in either its “-i” or “-o” command options; as a consequence, Shorewall does not allow them to be used in the /etc/shorewall/interfaces file or anywhere else except as described in the discussion below.
Most distributions have a facility for adding additional addresses to interfaces. If you have already used your distribution's capability to add your required addresses, you can skip this section.
Shorewall provides facilities for automatically adding addresses to interfaces as described in the following section. It is also easy to add them yourself using the ip utility. The above alias was added using:
ip addr add 206.124.146.178/24 brd 206.124.146.255 dev eth0 label eth0:0You probably want to arrange to add these addresses when the device is started rather than placing commands like the above in one of the Shorewall extension scripts. For example, on RedHat systems, you can place the commands in /sbin/ifup-local:
#!/bin/sh
case $1 in
eth0)
/sbin/ip addr add 206.124.146.178 dev eth0 label eth0:0
;;
esacRedHat systems also allow adding such aliases from the network administration GUI (which only works well if you have a graphical environment on your firewall).
On Debian and LEAF/Bering systems, it is as simple as adding the command to the interface definition as follows:
# Internet interface
auto eth0
iface eth0 inet static
address 206.124.146.176
netmask 255.255.255.0
gateway 206.124.146.254
up ip addr add 206.124.146.178/24 brd 206.124.146.255 dev eth0 label eth0:0The answer depends on what you are trying to do with the interfaces. In the sub-sections that follow, we'll take a look at common scenarios.
Note
The examples in the following sub-sections assume that the local network is 192.168.1.0/24.
If you need to make a rule for traffic to/from the firewall itself that only applies to a particular IP address, simply qualify the $FW zone with the IP address.
Example 3. allow SSH from net to eth0:0 above
[/etc/shorewall/rules]
#ACTION SOURCE DEST PROTO DEST PORT(S) ACCEPT net $FW:206.124.146.178 tcp 22
Suppose that I had set up eth0:0 as above and I wanted to port
forward from that virtual interface to a web server running in my local
zone at 192.168.1.3. That is accomplished by a single rule in the
/etc/shorewall/rules file:
#ACTION SOURCE DEST PROTO DEST PORT(S) SOURCE ORIGINAL # PORT(S) DEST DNAT net loc:192.168.1.3 tcp 80 - 206.124.146.178
If I wished to forward tcp port 10000 on that virtual interface to port 22 on local host 192.168.1.3, the rule would be:
#ACTION SOURCE DEST PROTO DEST PORT(S) SOURCE ORIGINAL # PORT(S) DEST DNAT net loc:192.168.1.3:22 tcp 10000 - 206.124.146.178
If you wanted to use eth0:0 as the IP address for outbound
connections from your local zone (eth1), then in
/etc/shorewall/masq:
#INTERFACE SUBNET ADDRESS eth0 192.168.1.0/24 206.124.146.178
Similarly, you want SMTP traffic from local system 192.168.1.22 to have source IP 206.124.146.178:
#INTERFACE SUBNET ADDRESS PROTO DEST PORT(S) eth0 192.168.1.22 206.124.146.178 tcp 25
Shorewall can create the alias (additional address) for you if you
set ADD_SNAT_ALIASES=Yes in
/etc/shorewall/shorewall.conf.
Warning
Addresses added by ADD_SNAT_ALIASES=Yes are deleted and re-added during shorewall restart. As a consequence, connections using those addresses may be severed.
Shorewall can create the “label” (virtual interface) so that you can see the created address using ifconfig. In addition to setting ADD_SNAT_ALIASES=Yes, you specify the virtual interface name in the INTERFACE column as follows.
/etc/shorewall/masq
#INTERFACE SUBNET ADDRESS eth0:0 192.168.1.0/24 206.124.146.178
Shorewall can also set up SNAT to round-robin over a range of IP addresses. To do that, you specify a range of IP addresses in the ADDRESS column. If you specify a label in the INTERFACE column, Shorewall will use that label for the first address of the range and will increment the label by one for each subsequent label.
/etc/shorewall/masq
#INTERFACE SUBNET ADDRESS eth0:0 192.168.1.0/24 206.124.146.178-206.124.146.180
The above would create three IP addresses:
eth0:0 = 206.124.146.178 eth0:1 = 206.124.146.179 eth0:2 = 206.124.146.180
If you wanted to use one-to-one NAT to link eth0:0 with local address 192.168.1.3, you
would have the following in
/etc/shorewall/nat:
#EXTERNAL INTERFACE INTERNAL ALL INTERFACES LOCAL 206.124.146.178 eth0 192.168.1.3 no no
Shorewall can create the alias (additional address) for you if you set ADD_IP_ALIASES=Yes in /etc/shorewall/shorewall.conf.
Warning
Addresses added by ADD_IP_ALIASES=Yes are deleted and re-added during shorewall restart. As a consequence, connections using those addresses may be severed.
Shorewall can create the “label” (virtual interface) so that you can see the created address using ifconfig. In addition to setting ADD_IP_ALIASES=Yes, you specify the virtual interface name in the INTERFACE column as follows.
/etc/shorewall/nat
#EXTERNAL INTERFACE INTERNAL ALL INTERFACES LOCAL 206.124.146.178 eth0:0 192.168.1.3 no no
In either case, to create rules in
/etc/shorewall/rules that pertain only to this NAT
pair, you simply qualify the local zone with the internal IP
address.
Example 4. You want to allow SSH from the net to 206.124.146.178 a.k.a. 192.168.1.3.
#ACTION SOURCE DEST PROTO DEST PORT(S) ACCEPT net loc:192.168.1.3 tcp 22
Sometimes multiple IP addresses are used because there are multiple subnetworks configured on a LAN segment. This technique does not provide for any security between the subnetworks if the users of the systems have administrative privileges because in that case, the users can simply manipulate their system's routing table to bypass your firewall/router. Nevertheless, there are cases where you simply want to consider the LAN segment itself as a zone and allow your firewall/router to route between the two subnetworks.
Example 5. Local interface eth1 interfaces to 192.168.1.0/24 and 192.168.20.0/24. The primary IP address of eth1 is 192.168.1.254 and eth1:0 is 192.168.20.254. You simply want your firewall to route between these two subnetworks.
In /etc/shorewall/zones:
#ZONE TYPE OPTIONS loc ipv4
In /etc/shorewall/interfaces:
#ZONE INTERFACE BROADCAST OPTIONS
loc eth1 - routeback In /etc/shorewall/rules, simply specify
ACCEPT rules for the traffic that you want to permit.
Example 6. Local interface eth1 interfaces to 192.168.1.0/24 and 192.168.20.0/24. The primary IP address of eth1 is 192.168.1.254 and eth1:0 is 192.168.20.254. You want to make these subnetworks into separate zones and control the access between them (the users of the systems do not have administrative privileges).
In /etc/shorewall/zones:
#ZONE TYPE OPTIONS loc ipv4 loc2 ipv4
In /etc/shorewall/interfaces:
#ZONE INTERFACE BROADCAST OPTIONS - eth1 -
In /etc/shorewall/hosts:
#ZONE HOSTS OPTIONS loc eth1:192.168.1.0/24 loc2 eth1:192.168.20.0/24
In /etc/shorewall/rules, simply specify
ACCEPT rules for the traffic that you want to permit.
For more information on handling multiple networks through a single interface, see Routing on One Interface.
Shorewall's support for Linux Vservers can (mis-)used to create a separate zone per alias. Note that this results in a partitioning of the firewall zone. In this usage, you probably want to define an ACCEPT policy between your vserver zones and the firewall zone.
